10Pcs Raindrops Rain Detection Sensor Module Weather Humidity
131
Direct purchase from the factory 
Idaniloju sisan
Ẹbun ọfẹ
Ilana gbigbe
Ilana padaẸbun Ọfẹ
Kaabọ si Roymall, oju opo wẹ ẹbun rẹ. A dupẹ lọwọ rẹ, a si pese ẹbun ọfẹ pẹlu eyikeyi rira. Ṣetan lati ṣawari akojo wa? Yẹra ni koko wa, fi aṣẹ rẹ sii, ki o si gba ẹbun ọfẹ rẹ.Ilana Gbigbe
A nṣe awọn aṣẹ laarin ọjọ 2.Gbigbe deede jẹ ọjọ 5-7.Akoko gbigbe le yatọ da lori ibudo.1. Ilana Pada
A gba nikan awọn nkan ti a ra lati roymall.com. Awọn ẹbun ọfẹ ko le pada. Nkan gbọdọ jẹ ailohunsi ati ni apoti atilẹba.A nṣe awọn pada laarin ọjọ 3-5 lẹhin gbigba.Awọn nkan aṣa ko le pada.Kan si wa: service@roymall.com tabi Whatsapp: +86193598494712.Ilana Isanwo
Iwọ yoo gba isanwo lẹhin gbigba nkan. A ko san owo gbigbe pada.Kan si wa: service@roymall.com tabi Whatsapp: +8619359849471
Description:
1. The item is for robot kit, raindrops, rain sensor, monitoring can be used for a variety of weather conditions, and converted into the number of the reference signal and the AO output.
2. The sensor uses the FR-04 high-quality double-sided materials, King Size 5.0 * 4.0CM, and with the surface of the nickel plating treatment, against oxidative, conductivity, superior performance and longevity;
3. The output in the form: digital switching outputs (0 and 1) and analog AO voltage output;
4. TTL-level output, TTL output valid signal is low. Driving capability 100MA so, can directly drive relays, buzzer, a small fan, and so on.
5. Sensitivity can be adjusted via potentiometer
6. LED lights up when there is no rain output is high, raindrop up, the output ground level, LED light.
Specification:
Small board PCB size: 3.2cm x 1.4cm
Operating voltage: 3.3V-5V
Voltage: 5V
Features:
1. Distribution bit to adjust sensitivity
2. A fixed bolt hole for easy installation
3. Power indicator, the output signal LED indicator
4. The comparator output, the signal is clean, waveform, driving ability over 15mA
5. Wide voltage LM393 comparator
6. A large area of rain board, more conducive to detect rain
7. Board with positioning holes to facilitate installation
8. Raindrops and control panels are separate, easy to wire leads
How to use:
1. Connected to 5V power supply, the power indicator light, sensor board is not water droplets, DO output is high, the switch lights off, dropping on a drop of water, DO output is low, the indicator light switch, Brush off the the above water droplets, has returned to output high state.
2. AO analog output can be connected to the microcontroller AD port to detect the size of the drops in the above rainfall.
3. DO TTL digital outputs can also be connected to the microcontroller detects whether there is rain.
Connection mode:
1. VCC: positive power supply (3-5V)
2. GND: negative one.
3. DO: TTL switching signal output
4. AO: Analog signal output
Package include:
10x Rain sensing board
10x Control board
10x 20cm Dupont Line set
1. The item is for robot kit, raindrops, rain sensor, monitoring can be used for a variety of weather conditions, and converted into the number of the reference signal and the AO output.
2. The sensor uses the FR-04 high-quality double-sided materials, King Size 5.0 * 4.0CM, and with the surface of the nickel plating treatment, against oxidative, conductivity, superior performance and longevity;
3. The output in the form: digital switching outputs (0 and 1) and analog AO voltage output;
4. TTL-level output, TTL output valid signal is low. Driving capability 100MA so, can directly drive relays, buzzer, a small fan, and so on.
5. Sensitivity can be adjusted via potentiometer
6. LED lights up when there is no rain output is high, raindrop up, the output ground level, LED light.
Specification:
Small board PCB size: 3.2cm x 1.4cm
Operating voltage: 3.3V-5V
Voltage: 5V
Features:
1. Distribution bit to adjust sensitivity
2. A fixed bolt hole for easy installation
3. Power indicator, the output signal LED indicator
4. The comparator output, the signal is clean, waveform, driving ability over 15mA
5. Wide voltage LM393 comparator
6. A large area of rain board, more conducive to detect rain
7. Board with positioning holes to facilitate installation
8. Raindrops and control panels are separate, easy to wire leads
How to use:
1. Connected to 5V power supply, the power indicator light, sensor board is not water droplets, DO output is high, the switch lights off, dropping on a drop of water, DO output is low, the indicator light switch, Brush off the the above water droplets, has returned to output high state.
2. AO analog output can be connected to the microcontroller AD port to detect the size of the drops in the above rainfall.
3. DO TTL digital outputs can also be connected to the microcontroller detects whether there is rain.
Connection mode:
1. VCC: positive power supply (3-5V)
2. GND: negative one.
3. DO: TTL switching signal output
4. AO: Analog signal output
Package include:
10x Rain sensing board
10x Control board
10x 20cm Dupont Line set
Products related to this item
Loading related products...
❮
❯
Videos for similar product
Loading product videos...
❮
❯
Electronics Ranking
